NISMO UCAs
Is anyone using the NISMO upper control arms? Thinking of trying them with my Rough Country 2.5” lifted struts (18”). Nissan mentions trimming the strut buckets for lifts over 1.5”. That can’t be very...
View ArticleMax Safe Bed Weight For My Suspention
2006 Nissan Frontier XE with the 4 cylinder engine. I am thinking of purchasing a small truck bed camper that weighs approx. 1,245.7 LBS & not loaded with gear. I know I will be pushing it but will...
View ArticleA warning about all dogs quality
So I've had all dogs rckilla hd springs and aal. I've been having issues with the aal pin keep coming loose and rattling. I reached out to them on June 1st with no answer wasn't looking for anything...
View ArticleSPC UCA bushing noise
2020 frontier, lifted 3.5 inches, SPC control arms. If anyone is lifted and has SPC UCAs and an unexplainable clunking noise when braking, accelerating, hitting bumps, turning, etc, check your SPC...
View ArticleDoes My Truck Already have a Body Lift?
2018 SV 4x4 Bought it used. Anyway looking at other trucks like it seems I have, by my eyes anyway, more clearance between top of tires and wheel well/ fender. I can also see the body a couple inched...
View Article4 wheel drive not shifting
My Nissan front frontier 2012 seems to be kind of jammed as it won’t shift between 2 Wheel Dr. four-wheel-drive, high or low. It seems to get stuck in one shift into the other. Also, the display on my...
View ArticleD40 Gross Vehicle Weight Rating (and thus payload capacity): 2005-2019, 2020+
So I've been looking at and thinking about the D40's GVWR, which for 14 years was 5,600 pounds. Then with the updated VQ38 powertrain in the 2020 models, the GVWR increased to 6,012 pounds, which is...
View ArticleAlignment Instructions to Give to Your Tech (via Brutal & nismo4x)
User BRUTAL has gone to some trouble to provide great information on how to get your truck aligned after a lift. Unfortunately, the information is scattered throughout the thread (and Brutal isn't...
View ArticleSway bar links need replacement every 6 months
My sway bar links are snapping in half at the bar or wearing out in 6 months. Are there other suspension components that could be worn and causing my sway bar links to fail prematurely? I’m a...
View ArticleHow-To/Review: Tundra Coilovers On a T Swap, Perfect Budget Coilover!
If you're on a budget for your T-swap and are doing it in stages this is pretty much the ideal setup. You may even find that you don't need the very expensive Radflos/SAWs. This setup will get you ALL...
View ArticleAll Dogs OffRoad Upper Control Arm Dust Shields ( Aftermarket )
Just picked these up, in red, 3d printed dust and water caps for the All Dogs Offroad upper control arms. They keep the ball joint pockets dry and protected from water, and debris. They have double...
View ArticleTundra Coilover Research/Data
PLEASE NOTE: This thread only applies to those that are titan swapped! NONE of these struts will work on your stock/ extended travel. Please see THIS thread for all the details regarding the Tundra...
View ArticleAlignment specs/ tire wear issues
I got my truck aligned about 3 months ago after doing the all dogs off-road ucas and finishing up the lift kit. Since then I have put about 5-6k miles on and have noticed my tires starting to wear on...
View ArticleADO 1/4" Spacer -- Z1 Fine Tuning Spacer
ADO 1/4" Spacer -- Z1 Fine Tuning Spacer Would anyone know exact measurements of these two? Does ADO measure exact to 1/4"?
View ArticleTitan swap no cut, is it possible?
Well as the topic states, can you do a titan swap on 33”s and not have to trim? Could you accomplish this with a taller bump stop? I’d be using stock pro4x wheels.
View ArticleClik here to view.
Reusing suspension nuts and bolts on UCA
Just wondering if people are reusing the nuts and bolts when installing new upper control arms. The reason I ask is because every video I could find shows them being reused yet the FSB says to replace...
View Article1 inch body lift good tire size
What would be a good mud terrain size for a 1 inch body lift on stock wheels.
View Articletie rod end boot
2010 Frontier Pro-4x- I have a outer tie rod boot from moog. The boot isn't seated, my question is can i place a large socket over it to seat over or do i need to get another one.
View ArticleConcrete Bucking/Bouncing on Gen2 (D40) Frontiers?
I've asked this in a variety of ways elsewhere, and I've seen a few threads, but I thought I'd ask it again. My Frontier bounces like crazy on concrete superslab interstate, especially those areas...
View ArticleWheel Spacers 0.5 to 0.75 inches
Hey what's up everyone, looking for your input here. I am hoping to add wheel spacers to my 2012 fronty pro4x to go along with a 2 inch ADO RCKILLA lift. The thing is I am looking for a slight and...
View Article
